touch issue for rza1lu_sample_guix_home_automation

Question

Hi All 
 
 I'm trying the GUIX demo on a Stream It board. 
 I completed the build and downloaded rza1lu_sample_guix_home_automation, rz_bsp , threadx, etc. 
 The initial screen is displayed, but the LCD touch does not work. 
 No changes have been made other than setting it to LCD565 in mcu_board_select.h. What should I check? 
 
 Regards.

GR Support · Answer

sorry. Please try to fix the other place. 
 static void channel1_port_init (void)
{
#if 1
 /* ---- P1_2 : SCL1 ---- */
 /* Port initialise */
 rza_io_reg_write_16( &GPIO.PIBC1, 0, GPIO_PIBC1_PIBC12_SHIFT, GPIO_PIBC1_PIBC12);
 rza_io_reg_write_16( &GPIO.PBDC1, 1, GPIO_PBDC1_PBDC12_SHIFT, GPIO_PBDC1_PBDC12);
 rza_io_reg_write_16( &GPIO.PM1, 1, GPIO_PM1_PM12_SHIFT, GPIO_PM1_PM12);
 rza_io_reg_write_16( &GPIO.PMC1, 0, GPIO_PMC1_PMC12_SHIFT, GPIO_PMC1_PMC12);
 rza_io_reg_write_16( &GPIO.PIPC1, 1, GPIO_PIPC1_PIPC12_SHIFT, GPIO_PIPC1_PIPC12);

 /* Port mode : Multiplex mode */
 /* Port function setting : 1st multiplex function */
 /* I/O control mode : Peripheral function */
 /* Bidirectional mode : Enable */
 rza_io_reg_write_16( &GPIO.PBDC1, 1, GPIO_PBDC1_PBDC12_SHIFT, GPIO_PBDC1_PBDC12);
 rza_io_reg_write_16( &GPIO.PFC1, 0, GPIO_PFC1_PFC12_SHIFT, GPIO_PFC1_PFC12);
 rza_io_reg_write_16( &GPIO.PFCE1, 0, GPIO_PFCE1_PFCE12_SHIFT, GPIO_PFCE1_PFCE12);
 rza_io_reg_write_16( &GPIO.PFCAE1, 0, GPIO_PFCAE1_PFCAE12_SHIFT, GPIO_PFCAE1_PFCAE12);
 rza_io_reg_write_16( &GPIO.PIPC1, 1, GPIO_PIPC1_PIPC12_SHIFT, GPIO_PIPC1_PIPC12);
 rza_io_reg_write_16( &GPIO.PMC1, 1, GPIO_PMC1_PMC12_SHIFT, GPIO_PMC1_PMC12);

 /* ---- P1_3 : SDA1 ---- */
 /* Port initialise */
 rza_io_reg_write_16( &GPIO.PIBC1, 0, GPIO_PIBC1_PIBC13_SHIFT, GPIO_PIBC1_PIBC13);
 rza_io_reg_write_16( &GPIO.PBDC1, 1, GPIO_PBDC1_PBDC13_SHIFT, GPIO_PBDC1_PBDC13);
 rza_io_reg_write_16( &GPIO.PM1, 1, GPIO_PM1_PM13_SHIFT, GPIO_PM1_PM13);
 rza_io_reg_write_16( &GPIO.PMC1, 0, GPIO_PMC1_PMC13_SHIFT, GPIO_PMC1_PMC13);
 rza_io_reg_write_16( &GPIO.PIPC1, 1, GPIO_PIPC1_PIPC13_SHIFT, GPIO_PIPC1_PIPC13);

 /* Port mode : Multiplex mode */
 /* Port function setting : 1st multiplex function */
 /* I/O control mode : Peripheral function */
 /* Bidirectional mode : Enable */
 rza_io_reg_write_16( &GPIO.PBDC1, 1, GPIO_PBDC1_PBDC13_SHIFT, GPIO_PBDC1_PBDC13);
 rza_io_reg_write_16( &GPIO.PFC1, 0, GPIO_PFC1_PFC13_SHIFT, GPIO_PFC1_PFC13);
 rza_io_reg_write_16( &GPIO.PFCE1, 0, GPIO_PFCE1_PFCE13_SHIFT, GPIO_PFCE1_PFCE13);
 rza_io_reg_write_16( &GPIO.PFCAE1, 0, GPIO_PFCAE1_PFCAE13_SHIFT, GPIO_PFCAE1_PFCAE13);
 rza_io_reg_write_16( &GPIO.PIPC1, 1, GPIO_PIPC1_PIPC13_SHIFT, GPIO_PIPC1_PIPC13);
 rza_io_reg_write_16( &GPIO.PMC1, 1, GPIO_PMC1_PMC13_SHIFT, GPIO_PMC1_PMC13);
#else
 set_pins_function( &GPIO_SC_INIT_riic1);
#endif
}

touch issue for rza1lu_sample_guix_home_automation

Top Replies